Відео

You explained best. I didn't understand it. Thanks!❤

I wonder what would happen, if you plugged 2 usbc chargers into it, at the same time?

You don't need to square anything for the dado. So long as the two templates are snug on both sides of the piece you're attempting to fit this will work fine. Note that I'm tempted to say "parallel" instead of snug, but the piece you're attempting to fit in the dado does not have to have parallel sides. So, put both templates snug against the piece to sit in the dado, clamp them up, remove the piece, route the slot, and you're done. No square, no parallel, no measurement. I did enjoy the simplicity of it and the explanation, just trying to remove the steps that aren't needed. Have a great weeked.

Can it be attached to a fire tablet? How?

How to connect this to app?

very good review

You need to get a stee combination square like Starrets for it not to slip. They're worth the price.

Can you please tell me what is the white wire that was tied to the foam insulated tubing?

They should make it easy to remove the fan guard so you can clean the blade surfaces and venting. It will greatly improve air flow and noise on any fan and needs to done often.

👍👍

Thank you!!

Like every other home assistant video it doesn’t work. I fucking hate home assistant

unfortunately qubicsdr has not maintained in 6 years and will not run on latest Macs .

Ok what if I have screwed up and downloaded it all over my computer And my op system is 10 pro but started with 7 8 8.1 Xp 10 10 pro I can clean up the computer but how do I wipe the dongle This time no smoking my medicine until I up and running

How about …inside the box….there is about a foot and a half of exposed pipe inside!

Useless review when it doesn't talk about how well it cools.

It’s garbage 1:32

Does not work. Don’t waste your money

Just bought one, assembled it and downloaded software. Can't get it to so anything but engrave and cut a small line. 😢

Its a peal and stick

I agree that part stores are ripping people off, and their web sites are terrible. I've had good luck with amazon parts.

Please help me. I buy this same cable but only appear some QR code for firmware upgrade. I already follow instructions on site when I scan that QR but same problem. I have IOS 17.5.1

Excellent video!!! Is there a significant decrease in charging speeds if you use the car's USB A port Rick?

Stop/tail lights and rear side marker lights bulb 7443, 194 for tail lights in this video and 168 for license plate lights.

But can you do the opposite? Can you connect two devices with Bluetooth receiving audio in and connect the audio jack to your headphones to hear your music and the game volume at the same time?

I work on cars a lot. Build guns. Just took my maschine apart. This gave me a 😅 when he mentioned fires n stuff, but i must say- doesnt look thattttt bad. A lot crazier than the 2012, but doable. Ill let you know how it goes- oh anyone new, read comments for best efficiency practices n watch more vids but this guy is A1(chip)

Thank you so much! Great video man. VERY Helpful. Keep it going!

😂

This saves me money 💴 thank you. But I order my Cabin air filter at e bay. Cheaper too but quality

Can you tell us at what point the fans kicked on and were they noisy at all or quiet?

Rick, glad to see you got onto another band with less family congestion. I might have to do that for the same reason…haha! Thanks!

Thank you. Followed all your instructions but when I opened the application (before even connecting the RTL SDR), I got the message CubicSDR quit unexpectedly. This comes with a lot of problem details & systems config reports, I tried this several times even doing a restart. I"m using a MBA M1 OS Sonoma 14.5. I also have McAffee installed. Any comment will be deeply appreciated.

It's fancy but does it work?

Great review

tried this with the Kasa Smart Plug Mini 15A but i dont get any energy monitoring :(

when ever i try sudo easy_install pip it says command not found. any solutions

İt's performance is good can I play Minecraft with this Intel nuc

Thank you 🙏🇱🇺🧀🌷☀️🍀🙂

Thank you for the review. Purchased for son to use with his electronics kit, a Radio Shack 150-in-1, the wooden one, which was mine when his age. An o-scope is critical for learning on these kits, but no kid could afford one way back then. This looks perfect!

Is the bitrate different for sw encoding different from videos to videos? I have a lot of .ts videos that I want to convey to .mp4 format, I've already setup batch conversion in a for loop, but looks like if I want to use hw encoding to run through all the videos faster, then I'd need to check their corresponding bitrate one by one to have comparable file size, so batching the process wouldn't work

Can this work with a 24V battery?

Rick nice review. However you did not address the input power specification is only 110Vac +/- 5% which is not sufficient for the typical U.S. Power. My power is provided by Edison in Southern California which states that input power for utilization equipment is 120Vac nominal with a range of (115Vac to 125Vac) which is outside this units input power specifications. If these units are really only specified for 110Vac +/- 5% this is a real problem. Do you think it is just a print error and it should really be 110Vac +/- 15%? Hope you can verify the correct input specification.

Dope vid thanks man!!! Really needed this video. First time ever building a tent 😅

I wonder if the cedar post version is steadier?

Your amazing

Olá amigo! Você sabe a potência de saída de som em mW?

always start the threads by hand. A deep socket or traditional is perfectly fine since you start the threads with your hands.

I have the exact same one. I love it.

Let’s say your car battery is removed, will this continue to power the ECM(car computer).

those are trash dont buy them